Onboard high-quality MP3 decoder. Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker. A MicroSD status LED. Onboard stereo 3.5mm audio jack socket for earphones. Onboard microSD socket for MP3 audio files storage. The interface from Arduino, UART, selectable to use soft serial. Stackable side headers. Supply voltage: 5V.
Based on NXP i.MX 8M SoC CPU Integrated GC7000 Lite Graphics Google Edge TPU Coprocessor Gigabit Ethernet Port Over 4 Trillion Operations ( tera-operations) per second (TOPS)
8bits colors support with 6bits correction for each color in every dots Hardware 16MHz PWM support 24 constant current channels of 100mA each Current Consumption(Except LED matrix): 20mA typical (40mA maximum) Drive current(Every channel):?500mA Drive current(Every dot) :?58mA
Comes with pre-programmed PIC18F4550 with USB bootloader. PIC18F4550 running at 48MHz (after PLL with 10MHz external crystal). Power via USB or external DC adapter (7 ?? 12V). On board 5V 800mA (Max 1A) voltage regulator. On board 3.3V 500mA (Max 500mA) voltage regulator. USB mini-B receptor for USB connection. 20 digital I/O pins. 6 analog input pin. 2 PWM output…
Implements CAN V2.0B speed up to?1 Mb/s SPI Interface speeds up to 10 MHz Standard (11 bit) and extended (29 bit) data and remote frames Two receive buffers with prioritized message storage Industrial standard DB-9 connector
TI AM5729 Dual-Core ARMCortex-A15 processor running at 1.5GHz Dual C66 DSP, Four ARM Cortex-M4, Four PRU, and Four Embedded Vision Engine Four Programmable Real-time Units (PRUs) Memory: 1GB RAM and 16GB on-board eMMC Flash Connectivity: Gigabit Ethernet, 2.4/5GHz WiFi, and Bluetooth USB-C for power and superspeed dual-role controller
Expansion Connector- Connection to BeagleBone / BeagleBone Black UART- Hardware UART to PRU Subsystem Sensors-Temperature sensor monitoring using a 1-wire interface Audio-Audio jack connection output GPIO-Dual GPIO push-button switch LEDs- Bank of PRU0 & PRU1 LEDs
EMW3166 Wi-Fi module with 256K SRAM，1M+2M Byte SPI Flash DAP Link emulator Micro USB 3.3V DC-DC, maximum current 1.5A Codec, with microphone and earphone socket
Get started with electronics quickly and easily without any prior experience because with this kit you will get an Official Arduino pictorial Project book
Input: 8x configurable digital / analog (0-10V) input Processor: STM32H747XI Dual ARM? Cortex?: Cortex -M7 core up to 480 MHz Cortex -M4 core up to 240 MHz Connectivity: Support 10/100 Ethernet (TCP/IP or Modbus TCP) USB-C
Powerful processor with integrated Deep Neural Networks in a tiny form factor (22.86 x 22.86 mm) Integrated microphone, magnetometer and smart 6-axis IMU Onboard Bluetooth? Low Energy connectivity Add speech recognition capabilities to your projects
ATSAMD11 ( Arm Cortex-M0+ @48 Mhz) microcontroller MP6522 motor driver Onboard 9-axis accelerometer, gyroscope, and magnetometer A battery charger for single-cell Li-ion batteries 2 ports for quadrature encoder counting A series of 3-pin male headers Easily connects actuators and sensors
Operating voltage 3.3V (supplied from the host board) Two relays with?NO,?COM,?and?NC?connections Works with battery-powered board Carry current: 2 A Max. operating voltage: 24 VAC, 50 VDC
