128Mb Flash(16M Byte) SBUS/PPM input (Pinheaders) DSM/DSM2/DSMX input(Plug) 6PWM output (Pinheaders) Only 36x36mm, mount holes 30.5×30.5mm All through hole pin header Design -no Sh connectors STM32 F405 MCU, Runs Raceflight CC3D REVO firmware Works Perfect with Raceflight or BetaFlight 3.0
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Run on SP RACING F3 EVO firmware 32 brush flight control Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight
CPU: STM32F030 Six-Axis: MPU6050 Firmware version: Silverware firmware Power Cable: 55mm, with JST-PH 2.0 connector ESC: All FETs are rated at 6A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors. Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
Wheelbase: 250mm Material: Full Carbon Fiber Weight: 160 gm The arm equips dampers for the safe landing. The arm has multiple motor mounting holes. Equips vibration-free mounting bracket for FPV camera.
Supports 6s LiPo battery Adjustable charge current from 1.0 to 20.0A The charger can store the charge current of the last charge program LED digits on indicate charge/discharge status Two working modes: balance charge mode and storage mode
2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6500). Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line. Fully pinout compatible with rev5 accessories (OSDoge etc). SBUS Inverter. Sonar pads w/resistors added for direct connection to 5V sonar. MS5611 barometer. 128mbit flash.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits onboard EEPROM for configuration storage.
Compact body design. High quality and durable performance. Light and portable to carry. Same size and hole, where CC3D. Integrated 2 switch control LED and FPV equipment. Element type: power distribution Board Use: for CC3D flight power controller distribute The same size and hole location as CC3D
₹3,814Original price was: ₹3,814.₹3,389Current price is: ₹3,389.
IC: Atmega644 PA Gyro/Acc: 6050MPU Input Voltage: 4.8V~6.0V AVR Interface: Standard 6 Pin Signal From Receiver: 1520us(5 channels) Signal to ESC: 1520 us
Axis: 2000 degrees/second 3-axis MEMS gyro. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line. Built-in FrSky telemetry inverter (shared w/main port). A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB). Onboard MicroUSB for setup and configuration. Multi WiFi-based configuration software for easy setup.
BEC output: 5V12V3A band filter Input Voltage: 2-6S(MAX: 3A) Weight: 9 gm(with connector) Latest UBEC, LC Filter Integrated filter circuit boards, more stable, make FPV further and clearer Compatible with CC3D/Naze32/F3 flight controller Slim design, lightweight, and easy to use
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Material: glass fiber Compatible with MK KK flight control installment pitch of holes Compatible with MK KK flight control system Can connect 1-8 ESC. Board Dimensions : 50 x 50 x 2 mm. Weight: 8 gm. Hole Spacing: 45mm Square and 35mm Square (Compatible with KK 45mm spacing)
Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery).