Sort by popularity Sort by average rating Sort by latest Sort by price: low to high Sort by price: high to low

• View:
• 12
• 24
• All

• • 
    Add to cart
  • Relay Boards

  • 4 Channel 5V Relay Module with Optocoupler

  • ₹169
  • 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current. Equipped with high-current relay, AC250V 10A; DC30V 10A. Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Indication LED’s for Relay output status.
  • 
• • 
    Add to cart
  • Relay Boards

  • ESP8266 ESP-01 5V WiFi Relay Module

  • ₹216
  • Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short response time
  • 
  • 
• • 
    Add to cart
  • Relay Boards

  • 5V Dual Channel Relay Module with Optocoupler

  • ₹100
  • Low Level Trigger Relay Module Two separate LEDs for On/Off indication of the Relay. Triggering input voltage 3.3V – 5V Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Back EMF protection 2 LEDs to indicate when relays are ON. Works with logic level signals from 3.3V or 5V devices…
  • 
  • 
  • 
• • 
    Add to cart
  • Relay Boards

  • 12V 4 Channel Relay Module

  • ₹253
  • 4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output status.
  • 
  • 
  • 
  • 
  • 
• • 
    Add to cart
  • Relay Boards

  • FR120N Mosfet control Module Replacement

  • ₹84
  • Model: FR120N MOS tube: 100V 9.4A Dimensions: 23mm X 16mm Mounting Holes Diameter: 2mm Compatible with MCU and control board, 3V or 5V signal. High-level start, low-level stop, PWM speed regulation.
  • 
  • 
  • 
  • 
  • 
• • 
    Add to cart
  • Electronic Modules and Displays, Relay Boards

  • 8 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM

  • ₹349
  • Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off;
  • 
  • 
  • 
  • 
• • 
    Add to cart
  • Electronic Modules and Displays, Relay Boards

  • Single Channel 5V Relay Module without Optocoupler

  • ₹42
  • High quality relay used 1-Channel Relay interface board Equipped with high-current relay : 12A @ 125V or 10AA @ 250V A Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM)
  •