Model: Adafruit Assembled Data Logging shield SD card interface: FAT16 or FAT32 Onboard regulator: 3.3 V Real time clock (RTC) keeps the time going even when the Arduino is unplugged
Implements CAN V2.0B speed up to?1 Mb/s SPI Interface speeds up to 10 MHz Standard (11 bit) and extended (29 bit) data and remote frames Two receive buffers with prioritized message storage Industrial standard DB-9 connector
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z…
8bits colors support with 6bits correction for each color in every dots Hardware 16MHz PWM support 24 constant current channels of 100mA each Current Consumption(Except LED matrix): 20mA typical (40mA maximum) Drive current(Every channel):?500mA Drive current(Every dot) :?58mA
Onboard high-quality MP3 decoder. Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker. A MicroSD status LED. Onboard stereo 3.5mm audio jack socket for earphones. Onboard microSD socket for MP3 audio files storage. The interface from Arduino, UART, selectable to use soft serial. Stackable side headers. Supply voltage: 5V.
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering connectors,…
Compatible with Arduino NANO All digital and analog pins breakout Compact size. Leads all pins out, convenient for wiring, and doing experiments. Dimensions: 53 x 36 x 12 (LxWxH) mm. Weight: 22 gm.
32-bit RISC architecture The processor can operate at 80MHz / 160MHz 32MB flash memory 64kB for instructions 96kB for data Standard native WiFi 802.11b / g / n Operates in AP, Station or AP + Station mode
Pin compatible with Adafruit Motor Shield Pin header to connect sensors and actuators. 4 H-Bridges L293D chipset. Surg Current Protection for IC L293D. Onboard On/Off Switch. Drive? 4 bi-directional DC motors Drive 2 Servo motors (unipolar or bipolar) On-board slot to connect HC-05/HC-06 Bluetooth modules for Wireless control via Smartphone
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
2 connections for 5V ?hobby? servos connected to the Arduino?s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or…
Compatible with Arduino NANO All digital and analog pins breakout Compact size. Leads all pins out, convenient for wiring and doing experiments. Dimensions: 53 x 36 x 12 (LxWxH) mm. Weight: 22 gm.
PS-2 connector Audio jack 3.5 mm connector Composite Video and Audio for RCA jacks VGA monitor connector 10 pin IO connector for Duinomite with cable A small ribbon cable with IDC10 connectors on both ends
Stable 5V powered, low current consumption, less than 150mA. 1 standard PS2 controller socket. Communicate with host microcontroller through 5V TTL?UART. Simple inquiry command and button status feedback for the host process. Vibrator motor is controllable. Wired or wireless PS2 controller is fully compatible. A small LED as the indicator for communication between SKPS and PS2 controller.
Analog Ports: include 4 anlog ports, A0, A1, A2 and A3. Digital Ports: include 7 digital ports, D2, D3, D4, D5, D6, D7 and D8. UART Port: 1 UART port. I2C Ports: 4 I2C ports.
Operating voltage: 5 V Tutorials for guidance Fully compatible with Arduino UNO High performance, low power 8 bit ATmega328 MU microcontroller Serial converter CP2102N chip (to communicate the Seeeduino with a computer by using a micro-USB cable) 2 on-board Grove connectors 14 Digital I/O Pins (6 PWM outputs) 6 Analog inputs ISP header Arduino UNO-R3 shield compatible Micro USB programming…
AD hoc IIC interface, APC220 wireless rf module communication interface RB URF v1.1 ultrasonic sensor interfaces Line 12864 LCD series and parallel interface More convenient and easy to use
The I2C input, PWM output control 16 roads, steering gear can 16 roads. The steering gear power independent V + input maximum 6 V. Logic signals and logical power independent output for 3V to 5 V. 40-1000 Hz frequency. Terminal block for power input. Reverse polarity protection on the terminal block input Green power-good LED
Stackable connectors ?? up to 6 channels can be stacked and wired to A0-A6 analogue inputs Calibration signal generation by D4/D9 digital output Precise trimmer potentiometer for calibration (all boards are shipped completely assembled, tested and calibrated so that you don??t have to do this unless you want to see how things works) Input connector for?standard?or active electrodes Works with…
Simple to use UART protocol Vibrator motor on PS2 is controllable. Wired and Wireless PS2 controller is supported. PS2 Controller will automatically operate in analog mode. (Default) A status LED Jumper selector to select different UART Baud Rate (74880 (Default), 9600, 57600, 115200). Default: ?? when no jumper is attached. Jumper selectors to select different digital pin as UART ??…
It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green,…
Simple design, an adapter board combined use with Xbee products. Adapter the Xbee 20-pin to dual-row pins with 0.1-inch standard spacing (dual rows with 0.5-inch distance). Identifies the pin with the corresponding screen print. Free soldering to the board with female socket
Expand 14 digital IO interface (12 steering gear interface)and power Six analog IO interfaces and power One digital port interface for external power supply terminals Digital port external power supply and on-board electrical automatic switch One external power input terminals and one input needle RS485 interface (D0-RX, D1-TX, D2-EN) IIC/the I2C/TWI interface (A4-SDA, A5-SCL) SD card module interface
Stackable design, easy to plug into the ARDUINO development board. Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly. 3.3v and 5v dual power output. 3.3v and 5v IO compatible. USB2.0 protocol.
Size: 29 x 71 mm Combines the function of Arduino Screw Shield and Sensor Shield. Expand all of IO interfaces from Arduino. 3-Pin male headers for easy sensor/servo connection. The Screw terminal can be screwed directly to the terminal on the thread and is reliable and convenient.
