Ideal for programming and testing. An ideal device for programmers. Suitable for ICs up to 28 pins. Low contact resistance when the IC is in place. Lever action for easy insertion and removal. RoHS free.
Ideal for programming and testing. An ideal device for programmers. Suitable for ICs up to 40 pins. Low contact resistance when the IC is in place. Lever action for easy insertion and removal. RoHS free.
32 I/O pin all the leads. Classic ATmega16 minimum system, eliminating the hassle of soldering. Support chips: ATmega16/ATmega32 and chip which pin-compatible. Power supply: power adapter or external expansion pin power supply (not support ISP download interface power supply) DC-005 Power Block (supporting the transposon is 5.5*2.1mm). Reset: Power-on-reset and reset button. Power LED (D1) and the program run indicator…
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The working current: typical 5mA, standby current 1 microamp. Except for the…
Model: MICROCHIP Evaluation Kit, ATSAMD10 MCU Free Atmel IDE for development of C/C++ and assembler code for Atmel microcontrollers Programming and debugging the ATSAMD10 Xplained Mini You can programming the ATmega32U4 Using a Bootloader Xplained Pro extension headers can easily be strapped in
The PIC ICD2 PICKit2 PICKIT3 Universal Programming Adapter Programmer Board is designed to work in conjunction with the popular PICkit 2 or PICkit3 programmer.
Support the most popular programming PIC chips, read, encryption and other features! No external power supply, communication, and power is only a USB cable to print complete, without any cable. PICSTARTPLUS much faster rate than programming. Can easily read the contents of the chip program area. Automatic programming verification. Comprehensive information prompts, allowing users to understand the working state.
Support the most popular programming PIC chips, read, encryption and other features! No external power supply, communication, and power is only a USB cable to print complete, without any cable. PICSTARTPLUS much faster rate than programming. Can easily read the contents of the chip program area. Automatic programming verification. Comprehensive information prompts, allowing users to understand the working state.
Model: STM32F302R8T6 MCU Voltage: 3.3V, 5V, 7-12V Two push buttons for user and reset Three interfaces supported on USB. Virtual Com port, Mass storage and Debug port STM32 comprehensive software HAL library Supported by Integrated Development Environments (IDEs) including IAR, Keil, GCC based IDEs
USB VBUS or external source (3.3V, 5V, 7 to 12V) and power management access point USB communication (LD1), user LED (LD2), power LED (LD3) Two push buttons ?? USER and RESET USB re-enumeration capability ?? virtual com port, mass storage, debug port Supported by wide choice of IDEs including IAR, Keil, GCC-based IDEs
Model: STM32L432KC MCU Flexible power-supply options: ST-LINK, USB VBUS or external sources On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port STM32 microcontroller in 32-pin package
1.54 inch 240×240 pixel TFT color LCD with parallel interface and capacitive touchscreen I2S Audio CODEC, with a stereo headset jack, including analog microphone input and a loudspeaker output Stereo digital MEMS microphones MicroSD??card connector extension I2C extension connector 128 Mbit Quad-SPI Nor Flash
Support a wide range of chips: All kinds of 26, 27, 28, 29, 37, 39, 49, 50 parallel ROM, EPROM, EEPROM; 24, 25, 35, 85, 93, 95 Series EEPROM, Serial parallel ROM chips; Fully supporting to the 48-PIN chips of 64Mbits capacity; It also supports a variety of models of 51 series of microcontroller, AVR microcontroller, including ATMEGA series, ATtiny…
