MCU STM32H743 32-bit processor running at 480 MHz VTX ON/OFF Pit Switch ? Switch can be enabled using USER1 in the Beta flight Mode tab. H7 processor @480 MHz Bluetooth onboard 8 Motors outputs in plugs 128 MB flash for logging VTX On/Off switch
High-performance STM32H743 Processor with more computing power & RAM New cost-effective design with the low-profile form factor A newly designed integrated vibration isolation system to filter out high-frequency vibration and reduce noise to ensure accurate readings IMUs are temperature-controlled by onboard heating resistors, allowing the optimum working temperature of IMUs
MCU: STM32F405RGT6?32-bit processor IMU: ICM20689 (SPI) USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 3 hardware UARTS (UART1,3,6) 128 Mbit Dataflash chip for Blackbox logging 5v Power Out: 1.5 A max 3.3v Power Out: 200 mA max
Length: 7mm rubber/ 4.5mm screw length Installation groove diameter: diameter of 2.3 mm. Weight: 3gm. On the shock-absorbing effect can be significant.
Model: Mamba F4 pro V2 Input voltage: 2 ?? 6s LiPo support Gyroscope: MPU6000 (reserved external gyroscope interface) Firmware: BetaFlihgt 3.2.0 OMNIBUSF4SD Support Receiver: PPM, SBUS, IBUS, DSM2/DSMX Receiver (UART1) Integrated with OSD, support BF Ground Station adjust OSD Adjust the PID by OSD by remote control
Model: Mamba F4 pro V2 Input voltage: 2 ?? 6s LiPo support Gyroscope: MPU6000 (reserved external gyroscope interface) Firmware: BetaFlihgt 3.2.0 OMNIBUSF4SD Support Receiver: PPM, SBUS, IBUS, DSM2/DSMX Receiver (UART1) Integrated with OSD, support BF Ground Station adjust OSD Adjust the PID by OSD by remote control
ATmega328P with Arduino bootloader. MAX7456 monochrome on-screen display. +5V 500mA regulator for up to +12V supply input. FTDI cable compatible pinout. The standard 6-pin ISP header. Standalone, or with APM/ Flip / Flip32+ flight controllers.
ATmega328P with Arduino bootloader. MAX7456 monochrome on-screen display. +5V 500mA regulator for up to +12V supply input. FTDI cable compatible pinout. The standard 6-pin ISP header. Standalone, or with APM/ Flip / Flip32+ flight controllers.
ATmega328P with Arduino bootloader. MAX7456 monochrome on-screen display. +5V 500mA regulator for up to +12V supply input. FTDI cable compatible pinout. The standard 6-pin ISP header. Standalone, or with APM/ Flip / Flip32+ flight controllers.
USB connector is used to connect to the USB port on your GoPro Hero3 Camera. The 3 pin female connector is for AV video output Typical application: Video output from your GoPro Hero 3 USB port to your video wireless transmitter. (Connect your GoPro Hero 3 directly to FPV transmitter)
USB connector is used to connect to the USB port on your GoPro Hero3 Camera. The 3 pin female connector is for AV video output Typical application: Video output from your GoPro Hero 3 USB port to your video wireless transmitter. (Connect your GoPro Hero 3 directly to FPV transmitter)
Axis: 2000 degrees/second 3-axis MEMS gyro. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line. Built-in FrSky telemetry inverter (shared w/main port). A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB). Onboard MicroUSB for setup and configuration. Multi WiFi-based configuration software for easy setup.
Axis: 2000 degrees/second 3-axis MEMS gyro. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line. Built-in FrSky telemetry inverter (shared w/main port). A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB). Onboard MicroUSB for setup and configuration. Multi WiFi-based configuration software for easy setup.
This is a breakout cable for the Naze32 flight controller This cable specially designed for open source flight controller such as Naze32 to connect with a radio receiver
