Serial to WIFI, Ethernet, Ethernet to Wifi multifunction Wifi module, transparent dual-way data transmission Integrated 10/100M ethernet port, Max. baud ratio up to 230.4kbps Adopts Ralink program, high-quality material Reliable system core suit safety and long-run system application Working temperature: industrial class -25~75?C
5V power supply. Serial I2C control of LCD display using?PCF8574. Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Multiple specifications compatible: M.2(A KEY) 2230/2242 to M.2(M KEY) 2260/228 LED indicators: the LED1 will light up when the device is driven successfully, the LED2 keeps off by default Outline Dimensions: 80×22.5 mm
SPI mode. Supply voltage: 4.5 ?? 5.5V. Up to 50 MB / sec data transfer rate. Located directly on a RAMPS. Also, be used with other microcontrollers. Dimensions: 27 x 17 x 11 mm(LxWxH). Weight: 5 gm.
Interface: USB 3.0 Read and write speed: above 200M/S Supports 3*5cm mSATA SSD to USB 3.0 interface. Compatible with Windows 2000/XP/Vista/7/8/Macos 7.0 and above.
IC Chip: MAX3232 Operating Voltage: 3.3-5.5V It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU Pre-assembled compact size?board Suitable for use with most microcontrollers Operates up to 250 kbit/s
IC Chip: SP3232E Operating Voltage: 3.0V ?? 5.5V Pre-assembled compact size?board Suitable for use with most microcontrollers ESD enhanced Hardware flow control supported
RS422 interface, two-way communication. B Y Z A ultra far transmission 1000 meters The module has ESD 15KV protection. Onboard to increase the limit of 10 ohms current limiting current protection. Module with TVS diode. Anti lightning, peak voltage. The module has 120-ohm termination resistors, which can effectively reduce the interference of long-range communication.
Recommended Input Voltage: 12V Input Voltage Range: 5-15V 2 Pin 2mm SMD JST Right-angle Connector for Input supply On-board TPS62133RGTT Synchronous step down DC-DC converter. Power Status LED (RED) Micro USB for Communication with Android. One start LED connected to boot pin (RC12 =Pin no. 39). User Switch SW1, SW2 connected to any port pin through SW1, SW2 Jumper respectively.
Onboard TJA1050 CAN controller interface chip Chip commonly used pin has led, convenient connection to use Pin 5 v to the power supply PCB board size: 22 (mm) x11.5 (mm) Fully compatible with the ISO 11898 standard High speed (up to 1 Mbaud)
Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc. Enhanced configuration devices: EPC1, EPC4. Supports 3 download mode: AS, PS and JTAG.
Logical light indication: a small light indicate CHO electrical level. Input feature: 5PF,100K Ohm. USB power supply; USB logic analyzer for monitoring, analyzing and debugging digital circuits 8-Channels USB logic analyzer with a 24Mhz sampling frequency Can analyze UART, IIC, and SPI, etc automatically Great for MCU, ARM system and FPGA development Voltage: 0-5.5V
