Name: 2G 3G IPEX antenna Connector type: ipx13 Gain definition: 3dBi (Typical) Frequency band definition: 17102170MHz 800960 Impedance definition: 50 ohm Total length: as shown in Figure Impedance 50 Ohm
Power supply: 3.7V 14500 Lipo battery Or 3.7~12Vdc power Operating Frequency: 915 MHz Size: 40mm x 60mm ATmega328P 8MHz with 3.3V logic/power 3.3V regulator with 500mA peak current output
Power supply: 3.7V 14500 Lipo battery Or 3.7~12Vdc power Operating Frequency: 915 MHz Size: 40mm x 60mm ATmega328P 8MHz with 3.3V logic/power 3.3V regulator with 500mA peak current output
Power supply: 3.7V 14500 Lipo battery Or 3.7~12Vdc power Operating Frequency: 915 MHz Size: 40mm x 60mm ATmega328P 8MHz with 3.3V logic/power 3.3V regulator with 500mA peak current output
2.4GHz applications 3.2dBi gain Antenna Connector: RP-SMA Male. 360º Rotation and tilt capabilities Omni-directional radiation. Antenna Type: Whip, Tilt. Max Height of Antenna: 19 cm
Range in open space(Standard Conditions) : 100 Meters RX Receiver Frequency : 433 MHz RX Typical Sensitivity : 105 Dbm RX Supply Current : 3.5 mA RX IF Frequency : 1MHz RX Operating Voltage : 5V TX Frequency Range : 433.92 MHz TX Supply Voltage : 3V ~ 6V TX Out Put Power : 4 ~ 12 Dbm
The smallest 802.11b/g/n Wi-Fi SOC module Up to 160MHz clock speed Built-in 10 bit high precision ADC UART baud rate up to 4Mbps Low power 32-bit CPU, can also serve as the application processor
The smallest 802.11b/g/n Wi-Fi SoC module Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA
The smallest 802.11b/g/n Wi-Fi SOC module Up to 160MHz clock speed Built-in 10 bit high precision ADC UART baud rate up to 4Mbps Low power 32-bit CPU, can also serve as the application processor
₹649Original price was: ₹649.₹531Current price is: ₹531.
Onboard ESP32-S module, supports WiFi + Bluetooth OV2640 camera with flash Onboard TF card slot, supports up to 4G TF card for data storage Supports WiFi video monitoring and WiFi image upload Supports multi sleep modes, deep sleep current as low as 6mA Control interface is accessible via pinheader, easy to be integrated and embedded into user products
Manufacturer: Ai-Thinker Low power 32-bit CPU, can also serve the application processor Support UART/SPI/I2C/I2S/PWM/ADC/DAC interfaces. Built-in 520 KB SRAM, external 4MPSRAM Supports audio input methods such as MIC and Line-in. Support for firmware upgrade (FOTA)
Manufacturer: Ai-Thinker 802.11b/g/n Wi-Fi+BT SOC Dual-core 32-bit CPU, 240 MHz frequency Built-in two 12 bit SAR ADCs, up to 18 channels Supports UART/SPI/I2C/SDIO/GPIO/ADC/PWM SMD38 package Supports OpenOCD debug interface UART baud rate up to 4Mbps
Very Few External Components Excellent Receiver Sensitivity and Robustness to Interference. Programmable Output Power Up to 4.5 dBm. High-Quality Construction
Capable of accepting all worldwide Coins and Tokens. Intelligent CPU software control, and high accuracy . Self-programming without PC. Accept 1-3 different kind of coins at the same time. Free to set up pulses' output. Prevent not only electric shock but also electromagnetic interference. Automatic self-test for problems. Free to set up the value for working. (APmode)
Serial Data Interface: Uart, Spi, I2c. Configuration Method: API Or At Commands, Local Or Over-the-air. Frequency Band: ISM 2.4 GHz. Form Factor: Micro, Through-hole, Surface Mount. Interference: Immunity Dsss (Direct Sequence Spread Spectrum). Adc Inputs: (4) 10-bit Adc Inputs. Digital I/o: 15.
168 dB maximum link budget. +20 dBm – 100 mW constant RF output vs. +14 dBm high-efficiency PA. Programmable bit rate up to 300 kbps. High sensitivity: down to -148 dBm. Bullet-proof front end: IIP3 = -12.5 dBm.
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface.
The smallest 802.11b/g/n Wi-Fi SOC module Up to 160MHz clock speed Built-in 10 bit high precision ADC Supports UART/GPIO/IIC/PWM/ADC Integrated Wi-Fi MAC/BB/RF/PA/LNA
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)
Communication interface voltage: 3.3V Working current: 240mA(MAX) Serial port baud rate: 115200 (default), can be modified to other values by AT command Serial communication format: 8N1 Wireless Network Mode: station / softAP / SoftAP + station Wireless criteria: 802.11 b / g / n WIFI @ 2.4 GHz, support for WPA / WPA2 security mode +19.5dBm output power
Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled Arduino-like hardware IO Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLL, regulators, DCXO and power management units Onboard USB to serial chip to easily program and upload codes from the Arduino IDE Embeds logic level converter circuits Has onboard 3.3V regulator to ensure enough power to function…
This GPS/GLONASS GNSS Antenna is designed for applications which require high positioning accuracy by combining signals from GPS, GLONASS, systems. The tiny size of this antenna allows it to be used in very space restricted environments.
Bluetooth protocol: Bluetooth Specification v2.0+EDR. Frequency: 2.4GHz ISM band. Modulation: GFSK(Gaussian Frequency Shift Keying). Emission power: =4dBm, Class 2. Sensitivity: =-84dBm at 0.1% BER. UART interface and with baud rate setup function
Bluetooth protocol: Bluetooth Specification v2.0+EDR Frequency: 2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) Emission power: ≤4dBm, Class 2 Sensitivity: ≤-84dBm at 0.1% BERCSR Bluetooth Chip Solution Enhanced Data Rate (EDR) compliant with V2.0.E.2 of the specification for both 2Mbps and 3Mbps modulation modes Full Speed Bluetooth Operation with Full Piconet Support and Scatternet Support Incredible small size with 3.3V…
Input Supply voltage (VDC) 3.6 ~ 6 Input current (mA) 50 Maximum Operating Range Distance 10 Meters Operating Frequency 2.4GHz ISM band Modulation GFSK (Gaussian Frequency Shift Keying) Emission power 4dBm, Class 2 Sensitivity -84dBm at 0.1% BER Operating Temperature (℃) -20 ~ 75
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes.
Operating Frequency Range: 433.4—473.0MHz Transmit Power Max: 20dBm Power Supply Voltage: DC 3.2V ~5.5V Long Communication Distance: About 1000 meters at the default setting
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate.
Standard:FCC/CE-RED/IC/TELEC/KCC/SRRC/NCC (ESP32 chip) Protocol:802.11 b/g/n Frequency range:2.4GHz~2.5GHz(2400M~2483.5M) Transmit Power:22dBm Communication distance:300m The wireless communication module supports cloud server development and SDK for user firmware development.
Compatible with 3.3v or 5v I/O Arduino Board. Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in a factory) Low power consumption Compatible with Arduino Leonardo, Uno, Mega, DUE External Antenna via I-Pex connector
Voltage supply: 3-5V (Battery) / 5V(USB Type C) Voltage output: EN 3V3 / 5V Power output Up to +20.8dBm at 3.3V Frequency: 865 Protocol: LoRaWAN Sensitivity: -116.5dBm ~ -136dBm
Sensitivity <-105 Supports voice calls Support news SMS Supports GPRS data services, maximum data rate, download 85.6 kbps, upload 42.8 kbps Support GSM / GPRS quad-band frequency bands, including 850, 900, 1800, 1900MHZ
Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI, AVR, PIC, LPC, STM32.
Radome material: polyurethane Flexible cable Stable signal Best for indoor applications. Connector: IPX female to SMA-KY Frequency(Hz): 900/1800 Gain: <3 dB VSWR: <1.5
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). Super Sense Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna.
Ready to Connect to PIXHAWK FC with 6-pin connector Attached Receiver type 72-channel M8 engine Galileo-ready E1B/C (NEO-M8N) Nav. update rate1 Single GNSS: up to 18 HZ Acquisition Cold starts: 26 s Onboard Compass
Model: RFM69HCW Frequency:868MHz Power Output Capability:+20 dBm 100 mW Sensitivity:-120 dBm at 1.2 kbps Selectivity:16-tap FIR Channel Filter FSK Bit rates:1.2kbps to 300kbps Voltage range:1.8V to 3.6V Module Size:16X16mm
Using RFM95 module based on SX1276 LoRa® ~28mA(Avg) @+20dBm continuous transmit ~8.4mA(Avg)@standby mode ~20mA(Avg) @receive mode, BW-500kHz Simple wire antenna or MHF Connector for external high gain antenna +20dBm – 100 mW Power Output Capability
Using RFM95 module based on SX1276 LoRa® Communication Interface: UART Simple wire antenna or MHF Connector for external high gain antenna +20dBm – 100 mW Power Output Capability
Quad-band 850/900/1800/1900MHz. GPRS class 2/10. Input Voltage : 9V-12V DC. Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set). Configurable baud rate. Built-in SIM Card holder. Built-in Network Status LED.
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal.
Standard AT commands Item Weight: 4.54 g Package Dimensions: 12.1 x 10.6 x 0.2 cm Adjustable serial baud-rate from 1200 to 115200 bps Single supply voltage: 3.4V – 4.5V Power saving mode: Typical power consumption in SLEEP mode is 1.5mA Frequency bands: SIM900A Dual-band: EGSM900, DCS1800. The SIM900A can search the two frequency bands automatically. The frequency bands also can…
Communication distance: 15KM Sensitivity: down to -148dBm Programmable bit rates: up to 300kbps RSSI dynamic range: 127dB Wireless frequency: 433MHz Working voltage: 1.8-3.7v Working temperature: -40-+80 ℃
LoRa Spread Spectrum modulation technology Constant RF power output at + 20dBm-100mW voltage change High sensitivity: down to -148dBm Half-duplex SPI communication Programmable bit rates up to 300kbps Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
Power Supply: Input USB 5V/1A Charging current :500mA Battery Input: 3.7-4.2V It also has a digital RSSI function, RF wake-up function, 4MB flash memory, Low voltage detection, and temperature sensor, Fast wake-up and frequency hopping LED signal indicator, and battery with data backup.
Material: CNC Aluminum alloy, carbon glass fiber rod Mounting rod diameter: 4mm Lead of rod: 14 cm. GPS plate diameter: 40 mm. Base plate diameter: 35 mm Mounting hole spacing: 16-35mm Weight: 20g Colour: Anodised black
Microcontroller: ESP8266EX Operating Voltage: 3.3V Digital I/O Pins: 11 (all I/O pins have interrupt/PWM/I2C/one-wire capability, except for D0) Analog Input Pins: 1 Flash Memory: 4MB On-Board Switching Power Supply: Input Voltage Range: 9V to 12V Output: 5V at 1A Max
Compatible with 3.3v or 5v I/O Arduino Board. Frequency Band: 433 MHZ (Pre-configure in factory) Low power consumption Compatible with Arduino Leonardo, Uno, Mega2560, DUE External Antenna via SMA Jack
168 dB maximum link budget. +20 dBm – 100 mW constant RF output vs. +14 dBm high-efficiency PA. Programmable bit rate up to 300 kbps. High sensitivity: down to -148 dBm. Bullet-proof front end: IIP3 = -12.5 dBm. Excellent blocking immunity. Low RX current of 10.3 mA, 200 nA register retention. Fully integrated synthesizer with a resolution of 61 Hz.…
Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile (3200m)
₹2,832Original price was: ₹2,832.₹2,419Current price is: ₹2,419.
Integrated, Wire Antenna Interoperable with other ZigBee-compliant devices Programmable versions with onboard microprocessor enable custom ZigBee application development Supports binding and multicasting for easy integration into a home automation platform Data Rate: RF 250 Kbps, Serial up to 1 Mbps Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m) Transmit Power: 3.1 mW (+5 dBm) Channels: 16…
