Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af compliant Low output ripple…
2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6500). Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line. Fully pinout compatible with rev5 accessories (OSDoge etc). SBUS Inverter. Sonar pads w/resistors added for direct connection to 5V sonar. MS5611 barometer. 128mbit flash.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits onboard EEPROM for configuration storage.
Compact body design. High quality and durable performance. Light and portable to carry. Same size and hole, where CC3D. Integrated 2 switch control LED and FPV equipment. Element type: power distribution Board Use: for CC3D flight power controller distribute The same size and hole location as CC3D
₹3,814Original price was: ₹3,814.₹3,389Current price is: ₹3,389.
IC: Atmega644 PA Gyro/Acc: 6050MPU Input Voltage: 4.8V~6.0V AVR Interface: Standard 6 Pin Signal From Receiver: 1520us(5 channels) Signal to ESC: 1520 us
Axis: 2000 degrees/second 3-axis MEMS gyro. Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line. Built-in FrSky telemetry inverter (shared w/main port). A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB). Onboard MicroUSB for setup and configuration. Multi WiFi-based configuration software for easy setup.
BEC output: 5V12V3A band filter Input Voltage: 2-6S(MAX: 3A) Weight: 9 gm(with connector) Latest UBEC, LC Filter Integrated filter circuit boards, more stable, make FPV further and clearer Compatible with CC3D/Naze32/F3 flight controller Slim design, lightweight, and easy to use
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Power supply voltage: DC2.5-12V Each channel has 800mA continuous current output Low saturation pressure drop TTL/CMOS output level compatible can be connected directly to the CPU Control and drive integrated into IC Have pin high-pressure protection function
L9110S-chip motor drive Supply voltage: 2.5-12V The maximum operating current of 0.8A Drive two DC motors or a 4-wire 2-phase stepping motor. Ultra-small size, suitable for assembly
The function of plug and play support 5V supports DC voltage input, and can also be powered by USB or mobile power supply. Truly Interactive – the latest software drivers will support a virtual touchscreen ‘on-screen’ keyboard, so there is no need to plug in a keyboard and mouse. Make your own Internet of Things devices including a visual display. Simply…
The function of plug and play support 5V supports DC voltage input, and can also be powered by USB or mobile power supply. Truly Interactive – the latest software drivers will support a virtual touchscreen ‘on-screen’ keyboard, so there is no need to plug in a keyboard and mouse. Make your own Internet of Things devices including a visual display. Simply…
