Quad-band 850/900/1800/1900MHz. GPRS class 2/10. Input Voltage : 9V-12V DC. Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set). Configurable baud rate. Built-in SIM Card holder. Built-in Network Status LED.
The shield can support being fully assembled with Arduino MEGA Support soldering components directly on this shield Support sticking the mini breadboards on this shield Reset button up top Mainboard aureate quadrate With SOP28 SMT components encapsulation
For Arduino UNO R3 Development Board only. With screw copper pillar and installation instructions. To protect your little computer against damages, dust and scratches Clear Top and Bottom. This case provides easy access to all ports. It requires no tools for easy assembly and disassembly. Simply Clicks Together Enclosure.
Use for – both raspberry pi zero w and v1.3 GPIO reference on the top of the case – you needn’t look at the GPIO reference from screen, paper or rule. The hole on the bottom of the case – you can change the case on the wall by the hole. Translucent color design – make the case more beautiful…
This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use. You just need to click them together after you fix your pi board on it with screws. 4 x Non-slip Silicone Gaskets provided, which…
This GPS/GLONASS GNSS Antenna is designed for applications which require high positioning accuracy by combining signals from GPS, GLONASS, systems. The tiny size of this antenna allows it to be used in very space restricted environments.
Sensitivity <-105 Supports voice calls Support news SMS Supports GPRS data services, maximum data rate, download 85.6 kbps, upload 42.8 kbps Support GSM / GPRS quad-band frequency bands, including 850, 900, 1800, 1900MHZ
Name: 2G 3G IPEX antenna Connector type: ipx13 Gain definition: 3dBi (Typical) Frequency band definition: 17102170MHz 800960 Impedance definition: 50 ohm Total length: as shown in Figure Impedance 50 Ohm
Using RFM95 module based on SX1276 LoRa® Communication Interface: UART Simple wire antenna or MHF Connector for external high gain antenna +20dBm – 100 mW Power Output Capability
Using RFM95 module based on SX1276 LoRa® ~28mA(Avg) @+20dBm continuous transmit ~8.4mA(Avg)@standby mode ~20mA(Avg) @receive mode, BW-500kHz Simple wire antenna or MHF Connector for external high gain antenna +20dBm – 100 mW Power Output Capability
Compatible with 3.3v or 5v I/O Arduino Board. Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in a factory) Low power consumption Compatible with Arduino Leonardo, Uno, Mega, DUE External Antenna via I-Pex connector
168 dB maximum link budget. +20 dBm – 100 mW constant RF output vs. +14 dBm high-efficiency PA. Programmable bit rate up to 300 kbps. High sensitivity: down to -148 dBm. Bullet-proof front end: IIP3 = -12.5 dBm. Excellent blocking immunity. Low RX current of 10.3 mA, 200 nA register retention. Fully integrated synthesizer with a resolution of 61 Hz.…
Compatible with 3.3v or 5v I/O Arduino Board. Frequency Band: 433 MHZ (Pre-configure in factory) Low power consumption Compatible with Arduino Leonardo, Uno, Mega2560, DUE External Antenna via SMA Jack
Power Supply: Input USB 5V/1A Charging current :500mA Battery Input: 3.7-4.2V It also has a digital RSSI function, RF wake-up function, 4MB flash memory, Low voltage detection, and temperature sensor, Fast wake-up and frequency hopping LED signal indicator, and battery with data backup.
"🎉 Enjoy exclusive discounts! Use coupon codes at checkout & get FREE delivery on eligible orders. Shop now! 🚚✨" Dismiss
