Channel: 1 channel Comes with GUIDE RAIL Relay Voltage: 5V High impedance controller pin Pull-down circuit for the avoidance of malfunction One normally closed contact and one normally open contact Triode drive, increasing relay coil
Channel: 1 channel Relay Voltage: 5V High impedance controller pin Pull-down circuit for the avoidance of malfunction One normally closed contact and one normally open contact Triode drive, increasing relay coil
Operating Voltage: 4.5-30 VDC It is a 2-wire display. LED Color: RED Current Consumption : < 15 mA. Accuracy: 0.1 V. Refresh Speed : Approx 200mS/time. Measure accurately up to? 3.6 V
Measuring Range: 0-100 VDC It is a 3-wire display. LED Color: GREEN Current Consumption : < 10 mA. Accuracy: 0.1 V. Refresh Speed : Approx 200mS/time. Measure accurately up to? 3.6 V
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short response time
5V power supply. Serial I2C control of LCD display using PCF8574. Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the microcontroller. Convenient RS-485 communication wiring Multiple Units can be…
Input voltage :10-32V Output voltage: 12-35V (adjustable) Output Current: 10A (MAX) Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A) The non-isolated step-up power conversion module Onboard LED illuminates when the voltage is applied to the module Equips Multi-turn Potentiometer.
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the…
Operating Voltage: 12V DC Port Size: 5.5mm (All 3 i/o are of the same size) Power: Pneumatic Pressure: Vacuum Operating Temperature (°C): -10 to 60 Type: Air Valve
Low Level Trigger Relay Module Two separate LEDs for On/Off indication of the Relay. Triggering input voltage 3.3V – 5V Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Back EMF protection 2 LEDs to indicate when relays are ON. Works with logic level signals from 3.3V or 5V devices…
1 Hz output pin SQW. 32 KHz output pin 32K. Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder.
"🎉 Enjoy exclusive discounts! Use coupon codes at checkout & get FREE delivery on eligible orders. Shop now! 🚚✨" Dismiss
