Analog Ports: include 4 anlog ports, A0, A1, A2 and A3. Digital Ports: include 7 digital ports, D2, D3, D4, D5, D6, D7 and D8. UART Port: 1 UART port. I2C Ports: 4 I2C ports.
Operating voltage: 5 V Tutorials for guidance Fully compatible with Arduino UNO High performance, low power 8 bit ATmega328 MU microcontroller Serial converter CP2102N chip (to communicate the Seeeduino with a computer by using a micro-USB cable) 2 on-board Grove connectors 14 Digital I/O Pins (6 PWM outputs) 6 Analog inputs ISP header Arduino UNO-R3 shield compatible Micro USB programming…
Supports Wi-Fi, USB host and SD cards Pin-out for PWM, I2C, SPI, UART, Ethernet, and I2S Open hardware board reference design including schematics, layouts and pin details Single input single output (1T1R) Wi-Fi 802.11 b/g/n. Pin-out for GPIO, I2C, I2S, SPI, UART, PWM and Ethernet Port. 580 MHz MIPS CPU. 32MB Flash and 128MB DDR2 RAM. USB host. Micro SD…
ATmega328P microcontroller Arduino UNO bootloader 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs ISP Header Arduino UNO-R3 Shield Compatible Micro USB programming and power supply 3 on-board Grove connectors 3.3/5V system operation power switch
AD hoc IIC interface, APC220 wireless rf module communication interface RB URF v1.1 ultrasonic sensor interfaces Line 12864 LCD series and parallel interface More convenient and easy to use
Retain the merits of the V4.0 version Laminated design PCB immersion gold processing technology IIC interface Bluetooth module communication interface SD card module communication interface APC220 wireless rf modules communication interface RB URF v1.1 ultrasonic sensors interface 12864 LCD string of line and parallel interface 32 servo controller interface
The I2C input, PWM output control 16 roads, steering gear can 16 roads. The steering gear power independent V + input maximum 6 V. Logic signals and logical power independent output for 3V to 5 V. 40-1000 Hz frequency. Terminal block for power input. Reverse polarity protection on the terminal block input Green power-good LED
Stackable connectors ?? up to 6 channels can be stacked and wired to A0-A6 analogue inputs Calibration signal generation by D4/D9 digital output Precise trimmer potentiometer for calibration (all boards are shipped completely assembled, tested and calibrated so that you don??t have to do this unless you want to see how things works) Input connector for?standard?or active electrodes Works with…
CPU -Allwinner F1C100s, ARM 926EJS processor, up to 900MHz Display ?? 40-pin RGB LCD FPC connector supporting 272×480, 480×800, 1024×600 Supports 720P video output, support video stream decoding such as H.264 / MPEG
CPU -Allwinner F1C100s, ARM 926EJS processor, up to 900MHz Display ?? 40-pin RGB LCD FPC connector supporting 272×480, 480×800, 1024×600 Supports 720P video output, support video stream decoding such as H.264 / MPEG
Chip built-in 128KB Flash, 32KB SRAM 4 x general purpose 16-bit timer, 2 x basic 16-bit timer, 1 x advanced 16-bit timer Watchdog, RTC, Systick 3 x USART, 2 x I2C, 3 x SPI, 2 x I2S, 2 x CAN, 1 x USBFS (OTG) 2 x ADC (10 channel), 2 x DAC
28nm process, dual-core RISC-V 64bit IMAFDC, on-chip huge 8MB high-speed SRAM (not for XMR :D), 400MHz frequency (able to 800MHz) KPU (Neural Network Processor) inside, 64 KPU which is 576bit width, supports convolution kernels, any form of the activation function.? APU (Audio Processor) inside, support 8mics, up to 192KHz sample rate, hardcore FFT unit inside, easy to make a Mic…
External supply voltage requirement: 5.0V?0.2V External supply current demand :> 300mA @ 5V Temperature rise :< 30K Range of working temperature :-30 ?C ~ 85 ?C
Onboard 5V regulator (78M05) circuit. On-Board power supply on-off switch On-Board DC motor Driver L298P On-Board 4×4 Matrix Keypad. On-Board 4 bit 16×2 LCD Display. 0592MHz crystal. Port extensions for all ports with detailed pin labelling for easy identification of pins Onboard USB TO Serial ?? CH340 Chip. On-board Micro USB USBASP for loading HEX file.
Microcontroller: ATMEGA2560 with 16 MHz crystal with On-Board USBASP Programmer. Power: 7 to 15 VDC with Reverse Polarity Protection. 2.4GHz ZigBee (XBee) wireless module adaptor 2×16 Character Alphanumeric LCD. SD card Holder. CH340G USB to Serial converter. ESP8255 Adaptor interface with USB to Serial Converter.
Simple to use UART protocol Vibrator motor on PS2 is controllable. Wired and Wireless PS2 controller is supported. PS2 Controller will automatically operate in analog mode. (Default) A status LED Jumper selector to select different UART Baud Rate (74880 (Default), 9600, 57600, 115200). Default: ?? when no jumper is attached. Jumper selectors to select different digital pin as UART ??…
USB Device up to 480Mbit/sec Capable of enumerating as a USB keyboard, mouse, joystick, MIDI, audio. Support 24-bit, 16-bit, and 8-bit CSI input It contains a Temperature sensor with programmable trim points
