Networking: Gigabit Ethernet RJ45 connector × 2 (Original Network port ETH0, and PCIE extended Network port ETH1) , mini?PCIE connector, supports 4G module (USB protocol, can not support PCIE protocol) ,? Nano-SIM card slot supports standard Nano-SIM card for 4G/3G/2G Internet access M.2: Dual NVME Solid State Drives slots (compatible with 2230, 2242, 2260, 2280) USB: USB 3.2 Gen1 (5Gbps)…
Adapter For NVMe Protocol M.2 SSD, Faster Reading/Writing, Improving Efficiency Supports Base Boards With PCI-E?1 / ?4 / ?8 / ?16 Socket Supports Raspberry Pi Compute Module 4 Compatible With Different Sizes Of M.2 SSD Slot Support-M Key(notch on the top right)
4x USB 3.2 Gen1 ports, USB 3.0 / 2.0 / 1.1 compatible Flexible power supply options: powered from either PCIe 12V, OR from 12V DC header Onboard VL805 chip, driver-free, plug and play
PL2303TA onboard the latest device, compatible with PL2303HXA 3 power mode: 5V output, 3.3V output, or powered by target board (3.3V-5V) 3 LEDs: TXD LED, RXD LED, POWER LED Supports windows XP/7/8/8.1/10
Model RS232/485/422 TO POE ETH (B) Product type Serial server, Modbus gateway, MQTT gateway Primary function RS232/485/422 to Ethernet Communication interface RS232/485/422 × 1, Ethernet port × 1 Power supply Screw terminal DC 6~36V or PoE network port Isolation protection Power isolation, signal isolation protection
HDMI-USB HUB Module: Expands 2x USB2.0 port, converts Mini HDMI port to standard HDMI port Zero POD case: Three-part structure design (aluminum alloy case + ABS top and bottom covers) Suitable for other Zero series boards.
Model: RP2040-One On-board Flash memory: 246KB of SRAM, and 4MB 2 x SPI, 2 x UART, 4 x 12-bit ADC, 16 x controllable PWM channels RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom Dual-core Arm Cortex M0+ processor, flexible clock running up to 133MHZ The castellated module allows soldering direct to carrier boards
Model: Waveshare Solar Power Management Module Solar panel input voltage : 6V~24V Micro USB input voltage : 5V Pinheader / USB output : 5V 1A Charging cutoff Voltage: 4.2V?1?
Supports MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel Flexible battery recharging: from the solar panel as well as USB TYPE-C power adapter Compatible with 6V~24V solar panels, DC-002 jack input or screw terminal input Heavy Aluminium body with a stylish finish and Multi status LEDs Batteries can be easily replaced by removing the cover.
5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver
Product: WIZnet W5500 Supports Wake on LAN over UDP Supports?High Speed Serial Peripheral Interface(SPI MODE 0, 3) Internal 32Kbytes Memory for Tx/Rx Buffers
LilyPad is a wearable e-textile technology.?Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They??re even washable!
5m total length. 60 LEDs/m. 24-bit color control (8-bit PWM per channel). 16.8 million colors per pixel. The one-wire digital control interface. Each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness. Waterproof.
