Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port.
1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system
Features standard USB Type A Connector, can be directly plugged to Laptop 3.3V and 5V dual power output 3 LEDs: power indicator, data reception indicator, the data transmission indicator, working status Meets the USB2.0 specification requirements
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Input voltage: DC 4.5 ~ 40V. Output voltage: 5V (when the input voltage is between 6.5V ~ 40V). Output current: 2A. The voltmeter has an automatic calibration function. With reverse connection protection. With overheat protection and short circuit protection.
Input : 6V-40V Output : 5V / 3A (MAX) Efficiency : 92% (MAX) Switching frequency : 150KHZ High efficiency and low ripple. With USB power indicator light. Maximum output 3A (at the same time with two mobile phones).
5V power supply. Serial I2C control of LCD display using PCF8574. Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Wide Input voltage: 3.5V-35V Output Voltage: 4-35V (Adjustable) Output current: rated current 3A MAX ( Heat-sink Needed) Conversion efficiency: Up to 92% (output voltage higher, the higher the efficiency) Switching Frequency: 50KHz
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications. Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch Interface for embedded applications
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V
Input voltage range: 4V-38V DC Output voltage range: 1.25V-36V DC adjustable. Output current: 0-5A. Output power: 75W. High efficiency up to 96% The built-in thermal shutdown function Built-in current limit function In-Built output short protection function
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Model: XL6019 Product: Adjustable Boost Power Supply Module Input Current: 5A (MAX) Input Voltage: DC 3-35 V Switching Working Temperature: Industrial (-40 ° C to + 85 ° C) Negative Output Voltage: DC 5-40V (Adjustable) Frequency: 220 kHZ
