Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz
Voltage: DC 2.4V – 5V Average Current Consumption: < 2mA Output mode: level or UART Detection distance: 2cm – 450cm Working temperature: -20°C to +70°C It features temperature compensation. Provides two output modes level or UART.
Onboard STM8S103 high-performance microprocessor With digital tube display Valid Measurement Distance: 3-400cm Display Unit: cm Maximum Input Voltage: 5VDC 2.54mm White Socket: 5V power interface.
High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array has mounting holes of…
Operating Voltage: 3.5V-5V Supply Current: 15mA Optimal Sensing Distance: 3mm Designed with the reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn)
Operating Voltage Range: 9~12V Maximum Operating Current: 130 mA Optimal Sensing Distance: 0.125″ (3 mm). Fast response time High sensitivity 5 Analog and 5 Digital Output signals with Respective LED. Each IR has indicating LED (D0-D4). Available SPI and Serial communication Pins.
Operating Voltage: 12V DC Measuring obstacle distance within 0 – 3 CM. Power Supply 3.3V – 5V Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection Mounting holes provided
Input voltage: 3.0 V – 5.5 V Output form: digital output (high and low level) Detection distance: 0 – 4 cm (black and white line sensors) 0 – 5 cm (adjustable distance detection)
Fast response characteristics Mounting holes to facilitate fixed installation The probe can plug design for easy testing. Signal light indicates the output Dual signal output (analog output, and TTL-level output) TTL output valid signal is low; (low output signal light, can be accessed by the microcontroller IO port)
Operating Voltage 4.75-5.25V Working Current Average current＜45mA Typical Power 225mW@5V Fully calibrated Standard digital output Excellent long-term stability
Supply voltage(V) 5 Operating temperature range (°C) -5~200℃ Complete calibration I2C digital interface communication Low power consumption :120mW(highest) Little lag error
Good sensitivity to CO/Combustible Gas High sensitivity to Methane, Propane, and CO Long life and low cost Simple drive circuit Input voltage: DC 5±0.2V Current Consumption: 150mA
Sensitivity to Ammonia, Sulphide and Benzene steam Sensitive for benzene, alcohol, smoke Fast response and recovery Adjustable sensitivity Signal output indicator Output voltage boosts along with the concentration of the measured gases increases.
Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. DO output: 0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.
Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm.
Using high-quality dual-panel design, with power indicator and TTL signal output instructions. The switching signal having a DO (TTL) output and analog output AO. TTL output valid signal is low. The higher the voltage, the concentration of the analog output voltage is higher. A hydrogen gas detection with good sensitivity. Has a long life and reliable stability
Detecting range: 300~10000ppm Signal output indicator. Dual Signal output (analog output and TTL output). The TTL output signal is low level, allows us to connect with SCM directly. Analog output 0~5V voltage. Quick response and recovery.
"🎉 Enjoy exclusive discounts! Use coupon codes at checkout & get FREE delivery on eligible orders. Shop now! 🚚✨" Dismiss
